Skip to content

Stainless Steel Welding in Fort Worth, TX

Monroe Mobile Welding repairs stainless steel tanks, tubing, sinks, and rails where they’re installed, across Dallas–Fort Worth, with AWS certified welders and more than 1,200 projects finished since 2012.

Tell us what the stainless part is, what runs through it, and where it sits. We’re often on site within an hour.

5.0 on Google
TIG torch welding a tube tee joint, the filler wire fed in beside the gas cup
Open
24/7After closing and between shifts
Arrival
Often within an hourKitchen, plant, farm, or site
Rate
$100–$300An hour, stainless included
Certified
AWSOur welders

When a stainless weld rusts, cracks, or won’t pass inspection

Stainless steel stays rust-free because of a thin chromium oxide film on its surface. A weld that’s overheated, left with heat tint, or cleaned with a carbon-steel wire wheel loses that film, and rust can show at the seam within days.

In a kitchen or food plant, a rough or pitted weld is more than a looks problem. Pits and crevices hold food and bacteria that cleaning can’t reach, and a leak at a tank fitting or process line stops production until it’s fixed.

Monroe Mobile Welding brings the welder to the stainless, so a tank, sink, prep table, or handrail doesn’t have to be pulled out and hauled to a shop.

  • Restaurants and commercial kitchens: prep tables, sinks, hood panels, and shelving
  • Food and beverage plants: process piping, tanks, and conveyor frames
  • Breweries: tank fittings, piping, and platforms
  • Dairy and farm equipment: milk tanks, sprayer tanks, and stainless lines
  • Stainless handrails, guardrails, and posts
Even TIG weld bead around a stainless steel pipe flange
A TIG weld around a stainless pipe flange.

Quick answers about stainless steel welding

Can you weld stainless steel on site?

Yes, where it sits.

Monroe Mobile Welding drives to your kitchen, plant, brewery, farm, or job site anywhere in Dallas–Fort Worth. We’re open 24/7 and often on site within an hour of your call.

How much does stainless steel welding cost?

$100 to $300 an hour.

Monroe Mobile Welding’s rate covers stainless the same as steel. The hours depend on the part, its thickness, and the cleanup the weld needs, so call (214) 501-8864 and describe the job.

Why is my stainless steel rusting at the weld?

Iron specks or heat damage, usually.

Most rust at a stainless weld starts with iron left by a carbon-steel brush or grinding disc, or with heat tint left on the seam. Monroe Mobile Welding can clean or cut out the bad weld and weld the joint again.

Should stainless be TIG or MIG welded?

TIG, for most repair work.

TIG welding lays a small bead with fine control of the heat, which suits tubing, thin sheet, and food-contact welds. MIG fits thicker stainless frames and brackets. Monroe Mobile Welding picks the process after seeing the part.

What keeps a stainless weld from rusting

Stainless resists rust only while its chromium oxide film is whole. These four things protect that film at the weld. Tell us on the call if the part touches food, carries chemicals, or faces an audit.

  • TIG welding with low-carbon filler rod

    Most stainless repair is TIG welded (tungsten inert gas), shielded with argon. The filler rod matches the steel: ER308L for 304 stainless, ER316L for 316. The L means low carbon, which keeps the metal beside the weld from losing its corrosion resistance.

  • Back-purging tubing, pipe, and tank seams

    The inside of a tube weld needs shielding gas too. Back-purging fills the tube with argon before and during the weld. Without it, the inside of the joint burns into a rough black crust welders call sugaring, which corrodes and traps product.

  • Brushes and discs kept for stainless only

    A wire brush or grinding disc that’s touched carbon steel leaves iron particles behind, and those specks rust on the stainless within days. Stainless work needs its own brushes and discs that never touch mild steel.

  • Heat tint removed, then passivated

    The straw, blue, or dark colors beside a weld are heat tint, a layer with less chromium than the steel under it. Pickling or polishing takes it off. Passivation, an acid treatment such as citric acid under ASTM A967, then helps the protective film rebuild.

Sanitary welds for food, beverage, and dairy lines

A sanitary weld is one a cleaning crew can keep clean. On equipment food or drink touches, the 3-A Sanitary Standards used across dairy and food processing call for welds that are continuous, fully penetrated, ground flush, and polished.

The grade matters too. 316 stainless carries molybdenum, which resists pitting from salt, acidic foods, and chlorinated cleaners better than 304. Tell Monroe Mobile Welding the grade if you know it, so the filler rod matches.

  • Full penetration, so no gap is left on the inside of the joint
  • A smooth inside surface with no sugaring, from a back purge
  • Ground flush and polished wherever food touches it
  • No tack welds, spatter, or pits that hold residue
  • Heat tint removed and the surface passivated

AWS certified welders, 1,200+ projects since 2012

Chad Monroe owns Monroe Mobile Welding, in business since 2012 and past 1,200 projects across Dallas–Fort Worth. Customers rate it 5.0 on Google.

  • AWS certified. Our welders hold American Welding Society certifications, including D1.1 for structural steel and D1.6 for stainless.
  • API 1104 certified. The American Petroleum Institute’s standard for welding pipe.
  • Licensed and liability insured on every job, in your kitchen or on your plant floor.
Since
2012
Projects
1,200+
Certified
AWS D1.6 · D1.1 · API 1104
Insured
Liability

Customers on the welds we left behind

One customer hired us after another welder’s bad job. These are Google reviews, word for word.

“Chris was highly professional, and communicated throughout the job. He came in after another welder left a terrible mess. Welds looked amazing and held. I highly recommend”

Daniel Rotter, Google review, October 2025

“His attention to detail and professionalism set him apart, and he works quickly without cutting corners.”

Aaron Ibarra, Google review, February 2025

“100% Quality welds and fast work”

Enrique Magana, Google review, February 2025

How a stainless repair runs

Three steps from your call to a repaired weld, with nothing hauled to a shop.

  1. Call (214) 501-8864

    Tell us the part, what it holds or carries, and where it is. Photos sent to [email protected] help us plan.

  2. We drive to you

    Kitchen, plant floor, brewhouse, farm, or stair rail, anywhere across Dallas–Fort Worth. We’re open 24/7, so the work can start after your last shift.

  3. We weld it in place

    Our AWS certified welders make the repair where the stainless is installed, at $100 to $300 an hour.

More questions about stainless welding

Can stainless steel be welded to regular steel?

Yes, with the right filler.

Stainless joins mild steel with a 309L filler, made to handle the mix of the two metals without cracking. Monroe Mobile Welding can weld those joints on site, on brackets, frames, and supports where stainless meets carbon steel.

Can you weld at night so our kitchen or line keeps running?

Yes, any hour.

Monroe Mobile Welding is open 24/7, so a stainless repair can happen after closing, between shifts, or during a weekend shutdown. Call (214) 501-8864 to set the time.

Is 316 stainless better than 304?

Against salt, acids, and cleaners, yes.

316 stainless contains molybdenum, which resists pitting from chlorides, acidic foods, and chlorinated cleaners. Monroe Mobile Welding welds both grades, each with its own low-carbon filler rod.

Do you fix stainless railings?

Yes, where they’re mounted.

Monroe Mobile Welding repairs broken welds on stainless handrails, guardrails, and posts where they stand, and does the same for steel gates and fences.

Need a stainless weld fixed on site?

(214) 501-8864
  • Open 24/7, often on site within an hour
  • [email protected]
  • Monroe Mobile Welding, 2080 Eagle Pkwy, Fort Worth, TX 76177. We come to you.
Call (214) 501-8864 Email